

Copyright © 2026 Fluent Conveyors, LLC. All rights reserved.
The Fluent Conveyors logo is a registered trademark of Fluent Conveyors, LLC. Serial Number 97664258 Registered on Dec. 12, 2023

Conveyor belt grades are codes that classify a belt's rubber cover by the conditions it resists, including abrasion, cuts, fire, static, heat, and oil. Each standard uses its own codes, so a letter such as E or Z can mean different things under different grading systems. U.S. specifications commonly call for ARPM Grade 1 or Grade 2. Learn how to read the grade on your belt and choose the right one.
A conveyor belt grade is a code for the class of rubber compound used on the belt cover. The applicable standard defines the code and the laboratory tests the cover must pass. Grades fall into two broad groups:
1. General-purpose and abrasion grades based on tensile strength, elongation, and abrasion loss
2. Special-service grades for conditions such as fire, static, heat, or oil
The grade describes the cover, which is the rubber in contact with the conveyed material. The fabric carcass underneath carries belt tension and has its own ratings. Two belts with the same cover grade can have very different strength ratings, ply counts, and cover thicknesses. Grade does not tell you whether a belt fits your conveyor.
Here's what each part of a complete belt specification covers:
A quote may not list a grade at all. Belt manufacturers often sell covers under proprietary compound names, and a U.S. supplier carrying several brands will often quote that name instead. The grade appears on the compound's data sheet, so ask for the sheet whenever a quote only lists a product name.
When we quote replacement belts, we supply the manufacturer's data sheet with the order.
Grade codes come from national and international standards, and no single code set applies worldwide. The same letter can mean different things. For example, Z is a light-duty abrasion grade under Germany's DIN 22102 and a special-properties grade under Australia's AS 1332.
Use this table to decode the grade shown on a belt or data sheet:
The Australian codes come from AS 1332-2000, which classifies covers as general purpose (M and N), abrasion resistant (A), static conducting (E), fire resistant (F), both static conducting and fire resistant (S), or special properties (Z), according to Australian Bulk Handling Review. The same source notes that M covers are harder, stronger, and more abrasion resistant than N covers.
Under DIN 22102, E, K, and S identify antistatic and flame-retardant covers. A conversion chart from German testing body DMT matches those letters to European EN 12882 safety classes 1, 2A, and 2B.
DIN's G identifies oil- or grease-resistant covers, but the letter does not set a resistance level, test method, or limit, according to a BulkInside guide to oil-resistant belting. If oil exposure is your concern, ask for oil swell test data along with the grade.
India's IS 1891 has separate parts for general-purpose, heat-resistant, oil-resistant, hygienic, and fire-resistant belting, as listed by the Bureau of Indian Standards. Part 1 covers come in grades M-24 and N-17, according to India's government procurement catalog. In Part 2, the BIS heat-resistant belting standard gives guideline temperatures for coarse material ranging from 257°F (125°C) for HR T1 to 356°F (180°C) for HR T3.
One common mix-up is that under both AS 1332 and DIN 22102, E means antistatic. Heat resistance uses other codes, such as India's HR classes for heat-resistant conveyor belts. If a quote gives a letter grade without naming the standard, ask which standard defines it.
U.S. belt specifications use two cover grades originally established by the Rubber Manufacturers Association (RMA). In 2010, RMA's non-tire members formed the Association for Rubber Products Manufacturers (ARPM), which now publishes the belt handbook. Older specifications that say "RMA Grade I" or "RMA Grade II" refer to the same two grades.
Both are abrasion-resistant covers, but they are intended for different damage patterns. Grade 1 suits sharp, abrasive material and severe impact, with greater emphasis on cut, gouge, and tear resistance while still providing strong abrasion resistance. Grade 2 handles abrasive material well but gives up some cut and gouge resistance, making it a cost-effective choice where material wears the cover without tearing deeply into it.
The 2011 edition of the ARPM IP-1 handbook sets these limits:
Both grades share the same minimum elongation, so the differences appear in tensile strength and abrasion loss. A lower abrasion-loss number means less rubber was removed during the test. ARPM revised the handbook in 2022, so confirm current values with your supplier before writing them into a specification.
For heavy crushed material over 3 inches (75 mm), the 2011 ARPM handbook points to Grade 1 when cut and gouge resistance is the main concern. That includes primary crusher discharge, large demolition rubble, and similar loads.
DIN grades also appear on U.S. quotes. DIN 22102 is the German belt standard; many imported belts are built to it, and suppliers carrying multiple brands may list a DIN grade beside an RMA grade or use it instead.
DIN grades are defined mainly by maximum abrasion loss, with tensile-strength and elongation minimums alongside it. The abrasion limits below come from a technical bulletin by Pooley Inc.:
DIN Y is the most commonly specified abrasion grade, according to an application engineering guide from Dunlop Conveyor Belting. It is the general-purpose cover found on many stocked rubber conveyor belts.
W and X address different types of damage. W allows the least abrasion loss, so it fits fine, gritty material such as sand and crushed glass fines. X allows slightly more abrasion loss but adds higher tensile strength and better cut resistance, making it better for sharp, lumpy material.
ISO 10247 classifies belt covers using the same three general properties. Its main classes are H for severe cut and gouge service, D for severe abrasion, and L for moderate service, as described in Martin Engineering's belting guide.
ISO 22721, the ISO specification for underground mining belts, lists these values:
Class D allows less abrasion loss than class H, even though H has higher tensile strength and elongation. Treat each letter as a service category rather than a ranking from best to worst.
ISO also specifies aging performance. Under ISO 22721's aging requirement, H, D, and L covers must keep tensile strength and elongation within 25% of their original values after 168 hours at 158°F (70°C).
Edition dates and how to verify an ISO claim on a data sheet are covered in our guide to ISO conveyor belt standards.
The systems address similar operating conditions, but each sets its own limits. Martin Engineering's grade comparison describes ISO H as roughly comparable to RMA Grade 1, while D and L approximate Grade 2. Australian and Indian letter grades follow their own test requirements.
This chart shows how the grades are commonly paired on quotes:
The test method is another important difference. DIN class limits use a non-rotating version of the ISO 4649 abrasion test, while the 2011 ARPM limits use the rotating version, which Pooley Inc.'s abrasion bulletin describes as a more severe test. Values produced by different methods cannot be compared directly, so check the test method listed beside each number on the data sheet.
Outside the U.S., standards often assign letter grades to special-service covers. U.S. specifications more commonly name the required property and the applicable test or approval. In either case, a special-service designation does not tell you how well the cover resists abrasion. ISO 22721's cover requirements state that oil, heat, and safety properties must be agreed separately between the buyer and belt manufacturer.
MSHA approval is a federal requirement for conveyor belts used in underground coal mines under 30 CFR Part 14. When the fire-resistant belting we supply carries an MSHA approval number, we pass that documentation through with the order.
Start with the damage you are trying to prevent, then work outward to the rest of the belt specification. This order helps avoid paying for an upgrade that does not address the actual problem:

Step 1 is the fastest place to begin. Our guide to types of conveyor belt damage shows what different wear patterns look like.
The table below shows how cover grades commonly line up with the materials our customers run. Treat these as starting points. The final specification still depends on the data sheet and actual loading conditions.
On single-stream recycling lines, broken glass often reaches belts originally specified for paper and plastic. If a fiber or container belt starts developing cuts, glass carryover is a likely cause. In that case, pricing a Grade 1 cover against repeated Grade 2 replacements may make sense.
Grades also apply to the rubber used on rubber combination roller chain belts, which mount rubber panels to roller chain for applications such as metering material into shredders. The same cut-versus-abrasion logic applies when choosing the compound.

Grade values come from laboratory tests on new rubber. ARPM states in its IP-1 conveyor belt handbook that there is no direct correlation between those test results and belt performance in service.
Cut and gouge resistance is even harder to quantify. No U.S. or international belt standard defines a laboratory test for it, according to a technical note from Pooley Inc., so belt manufacturers rely on their own in-house testing.
Check your belt’s markings or documentation to identify its grade and ensure it suits your application.

Send us photos of your worn belt and any paperwork you have. We build heavy-duty custom conveyors in the USA and supply replacement belting from leading belt manufacturers, so we can specify a belt compound resilient enough to handle your material.